The Master Frame is far from the 600 massive tower, but everything from cast-eelimenum corners to triple fan 360 mm format radiators talks about the desire to affect the cooler master. These corners of the corner provide the appearance of the shield that the cooler master earlier obtained using plastic Facebook Bits, which reduced the use of plastic to the use of plastic in things like power buttons and cable insulation. Even the ventilation holes in the front face are a bit “extra”: they are like the cooler master logo.
(Credit: Thomas Soderrom)
Plastic strength and reset buttons are rigid. Master Frame 600’s single indicator shines its power on signal through a hole in the LED aluminum panel. Twin USB 3.X Type-A ports, a typec port, and a headphone/mic (headset) Combo Jack complete a removable section located at the front end of the panel installed in the factory.
Around the back, we only find an outdoor panels made of steel instead of aluminum. These include an upper back panel that includes the center of the center with a 120 mm fan mount filled with a Mother Board I/O Plate and a factory, with eight slots PCI Express extension card panel, and the lower part with its power supply plate. These panels are capable of removing, but especially for the purpose of changing the power supply position from the bottom of the case. We do not see any provisions to convert PCI card slot holder into a side.
(Credit: Thomas Soderrom)
The bottom magnets and the bottom tabs enable toll -free access to the Master Frame 600 interior. Inside it, a set of horizontal cross bars saves a mother board tray and other interior panels in the outer frame. Two vertical bars can be distanced to mount a set of side fans or 3.5 -inch hard drives.
(Credit: Thomas Soderrom)
The master frame provides material for the damaged magnets of the frame to attract the sheet steel frames inside the aluminum face, up and right side panels. The dust filters are collided between the outer aluminum and the inner steel frames of the front and front panels, while plastic snaps place the right panel filter directly on its aluminum sheet using welded on stads.
The dust filter of the panel below is easy to remove. Since the under side is steel, its filter is stuck in place using magnetic strips.
(Credit: Thomas Soderrom)
From its cross rods, the master frame 600’s maternal board tray is around 1.3 inches, its cable cover is about 2 inches, and its triple 2.5 -inch drive tray is around 0.8 inches. All these pieces live behind all three of the 140 mm intake fans installed in the factory.
(Credit: Thomas Soderrom)
We mentioned various distances in which the entry panels stand to emphasize that they are not in the same plane. – Removing cable core Will; However, give builders enough to install the Mother Board of 9.6 to 10.7 inch enthusiasts, which also have EATX label. We just removed a panel down to the right to show where the side fan Mount lives.
(Credit: Thomas Soderrom)
Want more steel? Power supply shroud, removable end and cap, and panels beneath the hole steel are all eligible. So far, you are probably watching a continuous series of growing holes around the edge of the matter, which allows most of these ingredients to be reset.
(Credit: Thomas Soderrom)
Even the port panel can be moved down the front panel from the front panel. Given that it shares a section of the case with the adjacent panel, the above panel also needs to move the above panel to the front to move the port module to the front. Then the homeless front panel moves upwards.
Get our best stories!
All the modern tech tested by our experts
By clicking on the signup, you confirm that you are 16+ years old and agree to our use and privacy policy terms.
Thank you for signing up!
Your membership has been confirmed. Keep an eye on your inbox!
The biggest thing is, it gives the matter some spark of the future so that they can completely change the front and upward panels for new visits. The cooler master has yellow and black wooden finish parts, and more. For now, the cooler master site offers only one case panel (in the eucalyptus wood) as well as the interesting case panel panel stone (with a stone -like surface). Both master frames will fit into the upper or front parts of 600 case. We couldn’t find them in reality Is available Nowhere, though, and we are not sure if this optional bits will offer a cooler master.
The cables include HD audio, nine-pin power/reset buttons/LED front panel combination connector, a double link general 2 (ie general 2×2) cable in the type-e-Mother Board connector and a typec port, and 19 pin USB 3.X connectors with two type-A ports.
(Credit: Thomas Soderrom)
Removing the port unit (above) gives us a better view (below) how many holes are similar to the front and top panels: they are the same. Magnites have reached one end to connect the same front or above panel, and both are filled with multi -space brackets to install 120 mm to 200 mm fans. Here is the catch: The space available for the adjoining fans, which is taken by ports and buttons, reduces three 140 mm fans to three 120 mm.
(Credit: Thomas Soderrom)
